RAM Tab-Tite & Tab-Lock Size Guide: Which Cradle Fits My Tablet?

Short answer: measure your tablet in the case you'll actually use (height, width and depth), then find the cradle whose ranges cover all three numbers in the size chart below. Every RAM® Tab-Lock™ holder is the same size as its Tab-Tite™ twin (TABL20U pairs with TAB20U, and so on); the Tab-Lock simply adds a key lock.

RAM makes more than 30 Tab-Tite cradles, and the names don't help much: "9"–10.5" tablets with case" covers a lot of ground. So here's everything in one place. Start with the compatibility table if your tablet is a common model; use the size chart if it isn't listed or you're running an unusual case.

How to measure your tablet

  • Height: the long edge, measured with the case fitted. This is the direction the spring-loaded cups close on.
  • Width: the short edge, again in the case. The cups are a fixed width, so this is the measurement that most often rules a cradle out.
  • Depth: the thickness at the edge where the cups grip, not at the camera bump.

All three numbers need to sit inside the cradle's ranges. If your tablet has a hand strap on the back, you may need a set of 1/2" risers or 1" risers to lift the cups clear of it.

Tab-Tite vs Tab-Lock: what's the difference?

Both use the same spring-loaded backplate principle, the same interchangeable end cups and the same 4-hole AMPS mounting pattern, so they bolt to exactly the same RAM® ball bases and arms. The Tab-Tite is quick-release: pull the top cups up, lift the tablet out. The Tab-Lock adds a keyed lock (two keys supplied) so the tablet can't be pulled out of the cradle by someone else. Pick the Tab-Lock for work utes, fleet vehicles, hire gear, kiosks or anywhere the tablet is left unattended.

Not every Tab-Tite size has a Tab-Lock version. Where the Tab-Lock column below shows a dash, RAM doesn't make (or we don't currently list) a locking twin for that size.

Which Tab-Tite or Tab-Lock fits my tablet?

Common tablets and the cradle that suits them, split by whether you run the tablet bare (or in a thin sleeve) or in a protective case. "In a case" assumes a typical protective case; very bulky rugged cases should be checked against the size chart.

Tablet No case / light sleeve In a case
Tab-Tite Tab-Lock Tab-Tite Tab-Lock
Apple iPad
iPad mini 1 TAB2U, TAB-SMU TABL2U – –
iPad mini 2 / 3 TAB27U, TAB-SMU TABL27U TAB29U TABL29U
iPad mini 4 / 5 (TAB30U blocks the Lightning port) TAB30U – TAB29U TABL29U
iPad mini 6 / mini (A17 Pro) TAB2U TABL2U TAB12U TABL12U
iPad 1–4 TAB3U TABL3U TAB17U, TAB-LGU TABL17U
iPad Air / Air 2, iPad 9.7 (2018) TAB6U – TAB20U, TAB-LGU TABL20U
iPad 9.7 (2017) TAB28U TABL28U TAB20U TABL20U
iPad 7th / 8th / 9th gen (10.2") TAB26U, TAB8U TABL26U, TABL8U TAB20U, TAB8U TABL20U, TABL8U
iPad 10th / 11th gen – – TAB20U TABL20U
iPad Air 3 TAB26U TABL26U – –
iPad Air 4 / Air 5 TAB3U TABL3U TAB17U TABL17U
iPad Pro 9.7 TAB26U, TAB8U TABL26U, TABL8U TAB8U TABL8U
iPad Pro 10.5 TAB26U TABL26U TAB20U TABL20U
iPad Pro 11" (2018–2021) TAB3U TABL3U TAB17U TABL17U
iPad Pro 11" (4th gen, 2022) – – TAB19U, TAB17U TABL19U, TABL17U
iPad Pro 12.9" – – TAB10U TABL10U
Samsung Galaxy Tab
Tab A 7.0 TAB5U, TAB18U TABL18U TAB4U TABL4U
Tab 4 7.0 TAB22U TABL22U TAB21U –
Tab A 8.0 (2015 model) TAB27U TABL27U TAB29U TABL29U
Tab A 8.0 (2017 / 2018 / 2019) TAB24U TABL24U TAB23U TABL23U
Tab A 8.4, Tab A7 Lite 8.7 TAB24U TABL24U TAB12U TABL12U
Tab A9, Tab A11 TAB24U TABL24U TAB23U TABL23U
Tab S2 8.0 TAB30U – TAB29U TABL29U
Tab Active2 TAB-SAM29U, TAB23U TABL23U – –
Tab Active3 / Active5 TAB-SAM29U – – –
Tab Active Pro / Active4 Pro / Active5 Pro TAB6U – – –
Tab A 9.7, Tab A 10.5, Tab S2 9.7, S3 9.7, S4 10.5 TAB28U TABL28U TAB20U TABL20U
Tab A8 10.5 TAB28U TABL28U TAB33U TABL33U
Tab S6, S7, S8, S9, S9 FE TAB28U TABL28U TAB20U TABL20U
Tab S10 FE, S10 Lite TAB28U TABL28U TAB25U TABL25U
Tab A11 Plus TAB28U – TAB20U TABL20U
Tab S6 Lite, Tab A7 10.4, Tab S5e, Tab A 10.1 (2016) TAB33U TABL33U TAB33U TABL33U
Tab A 10.1 (2019) – – TAB25U TABL25U
Tab 4 10.1, Tab S 10.5 TAB26U TABL26U TAB25U TABL25U
Tab E 9.6 TAB31U – TAB25U TABL25U
Tab S7+, S7 FE, S9+, S9 FE+ – – TAB36U –
Tab S8+ – – TAB36U, TAB19U TABL19U
Rugged and other tablets
Panasonic Toughpad FZ-G1 (standard battery) TAB19U TABL19U – –
Panasonic Toughpad FZ-A1 TAB10U TABL10U TAB9U TABL9U
Panasonic Toughbook FZ-G2 / FZ-A3, Getac UX10 TAB34U TABL34U – –
Panasonic Toughpad FZ-M1 TAB12U TABL12U – –
Microsoft Surface Go / Go 2 TAB26U TABL26U TAB20U TABL20U
Microsoft Surface Pro / Pro 2 / Surface 2 / 3 TAB25U TABL25U – –
Amazon Fire 7 TAB18U TABL18U TAB4U TABL4U
Amazon Fire HD 8 TAB2U TABL2U TAB12U TABL12U
Amazon Fire HD 10 TAB6U – TAB19U TABL19U
Zebra ET50 / ET55 10" TAB25U TABL25U – –
Zebra ET5x 10" – – TAB19U TABL19U

Tab-Tite and Tab-Lock size chart

The ranges are the tablet sizes each cradle accepts (measured in its case, if you use one), taken from RAM's published fitment figures. Metric first, inches underneath.

Tab-Tite Tab-Lock Built around Height Width Depth
7" tablets
TAB22U TABL22U Galaxy Tab 4 7.0 (no case) 187.5–253.7 mm
(7.38–9.99")
76.2–108.0 mm
(3–4.25")
3.3–10.2 mm
(0.13–0.4")
TAB5U – Galaxy Tab A 7.0 (no case) 177.8–250.8 mm
(7–9.88")
87.4–119.4 mm
(3.44–4.7")
3.3–11.2 mm
(0.13–0.44")
TAB21U – Galaxy Tab 4 7.0 in OtterBox Defender 188.5–254 mm
(7.42–10")
91.4–115.8 mm
(3.6–4.56")
3.3–18.3 mm
(0.13–0.72")
TAB16U – Google Nexus 7 with case 190.5–250.8 mm
(7.5–9.88")
92.1–128.3 mm
(3.63–5.05")
3.3–20.8 mm
(0.13–0.82")
TAB18U TABL18U Nexus 7, Amazon Fire 7 (no case) 190.5–257.2 mm
(7.5–10.13")
95.3–119.4 mm
(3.75–4.7")
3.3–10.9 mm
(0.13–0.43")
TAB2U TABL2U iPad mini 1, mini 6, mini A17 Pro, Fire HD 8 (no case) 177.8–244.5 mm
(7–9.63")
101.6–134.9 mm
(4–5.31")
3.3–14.2 mm
(0.13–0.56")
TAB4U TABL4U 7"–8" tablets in a case 187.3–254 mm
(7.38–10")
101.6–134.9 mm
(4–5.31")
3.3–26.9 mm
(0.13–1.06")
TAB-SMU – Universal small (3 sets of cups), iPad mini 1–4 177.8–254 mm
(7–10")
101.6–134.9 mm
(4–5.31")
11.2–26.9 mm
(0.44–1.06")
8" tablets
TAB24U TABL24U Galaxy Tab A 8.0 (2017–2019), A 8.4, A7 Lite, Tab A9 (no case) 205.2–271.5 mm
(8.08–10.69")
95.8–125.7 mm
(3.77–4.95")
3.3–9.1 mm
(0.13–0.36")
TAB27U TABL27U Galaxy Tab A 8.0 (2015), iPad mini 2 / 3 (no case) 200–263.6 mm
(7.88–10.38")
109.2–134.6 mm
(4.3–5.3")
0–9.4 mm
(0–0.37")
TAB30U – Galaxy Tab S2 8.0, iPad mini 4 / 5 (no case) 198.6–263.5 mm
(7.82–10.38")
120.7–136.5 mm
(4.75–5.38")
0–7.9 mm
(0–0.31")
TAB12U TABL12U iPad mini 6 / A17 Pro with case, most 8" tablets with case 181–241.3 mm
(7.13–9.5")
128.5–144.3 mm
(5.06–5.68")
3.3–25.4 mm
(0.13–1")
TAB23U TABL23U Galaxy Tab Active2, 8" Galaxy tablets in a case 211.3–277.4 mm
(8.32–10.92")
112.5–134.6 mm
(4.43–5.3")
3.3–15.75 mm
(0.13–0.62")
TAB-SAM29U – Galaxy Tab Active2 / Active3 / Active5 215.9–263.5 mm
(8.5–10.38")
up to 132.8 mm
(up to 5.23")
up to 15.2 mm
(up to 0.6")
TAB29U TABL29U iPad mini 2–5 with case, Galaxy Tab A / S2 8.0 with case 209.6–279.4 mm
(8.25–11")
127–149.4 mm
(5–5.88")
7.6–17.1 mm
(0.3–0.67")
TAB-SM2U – Universal 8" (3 sets of cups) 205–279 mm
(8.08–11")
96–149 mm
(3.77–5.88")
3.3–17 mm
(0.13–0.67")
9"–10.5" tablets
TAB28U TABL28U Galaxy Tab S6 to S9 FE, Tab A 10.5, iPad 9.7 (2017) (no case) 228.6–298.5 mm
(9–11.75")
139.7–168.9 mm
(5.5–6.65")
up to 8 mm
(up to 0.31")
TAB26U TABL26U iPad 7th–9th gen, iPad Air 3, Galaxy Tab S 10.5 (no case) 238–307 mm
(9.38–12.11")
141–178 mm
(5.55–7")
3.3–8.6 mm
(0.13–0.34")
TAB33U TABL33U Galaxy Tab S6 Lite, A7 10.4, S5e (with or without light case) 242.6–299.7 mm
(9.55–11.8")
139.7–176.5 mm
(5.5–6.95")
5.1–16.8 mm
(0.2–0.66")
TAB31U – Galaxy Tab E 9.6 (no case) 238.1–301.6 mm
(9.38–11.88")
114.3–149.2 mm
(4.5–5.88")
0–7.9 mm
(0–0.31")
TAB6U – iPad Air / Air 2, Galaxy Tab Active Pro range (no case) 219–286 mm
(8.63–11.25")
154–173 mm
(6.05–6.8")
3.3–12.7 mm
(0.13–0.5")
TAB3U TABL3U iPad 1–4, iPad Air 4 / 5, iPad Pro 11" (no case or light case) 216–283 mm
(8.5–11.13")
162–197 mm
(6.38–7.75")
3.3–14.2 mm
(0.13–0.56")
TAB20U TABL20U iPad 5th–11th gen with case, Galaxy Tab S6 to S9 with case 241–308 mm
(9.5–12.13")
Tab-Lock: 235–308 mm (9.25–12.13")
166–189 mm
(6.55–7.43")
7.6–22 mm
(0.3–0.88")
TAB25U TABL25U Galaxy Tab S10 FE, Tab A 10.1 (2019) with case, Surface Pro / Pro 2 244.9–313 mm
(9.64–12.32")
155.7–188 mm
(6.13–7.4")
3.3–17.8 mm
(0.13–0.7")
TAB8U TABL8U iPad Pro 9.7, iPad 9th gen (with or without case) 229–292 mm
(9–11.5")
162–211 mm
(6.38–8.31")
3.3–28 mm
(0.13–1.12")
TAB17U TABL17U iPad 1–4, Air 4, iPad Pro 11" in heavy-duty cases 241–298 mm
(9.5–11.75")
162–210 mm
(6.38–8.25")
3.3–28 mm
(0.13–1.1")
TAB-LGU – Universal large: full-size iPads in heavy-duty cases 216–298.5 mm
(8.5–11.75")
197–209.6 mm
(7.75–8.25")
14.2–27.9 mm
(0.56–1.1")
11"–13" and rugged tablets
TAB10U TABL10U iPad Pro 12.9" in a case, Toughpad FZ-A1 247.7–304.8 mm
(9.75–12")
162.1–218.9 mm
(6.38–8.62")
3.3–25.4 mm
(0.13–1")
TAB9U TABL9U Toughpad FZ-A1 with case, Latitude 12 Rugged 269.9–320.7 mm
(10.63–12.63")
162.1–235 mm
(6.38–9.25")
3.3–50.8 mm
(0.13–2")
TAB19U TABL19U Toughpad FZ-G1, Galaxy Tab S8+ with case, iPad Pro 11" (4th gen) 273–340 mm
(10.75–13.38")
165–197 mm
(6.5–7.75")
3.3–23.6 mm
(0.13–0.93")
TAB34U TABL34U Toughbook FZ-G2 / FZ-A3, Getac UX10 266.7–317.5 mm
(10.5–12.5")
187.7–200.2 mm
(7.39–7.88")
25.4–31.8 mm
(1–1.25")
TAB36U – Galaxy Tab S7+ / S7 FE / S8+ / S9+ with case 292.1–355.6 mm
(11.5–14")
up to 206.4 mm
(up to 8.13")
up to 20.1 mm
(up to 0.79")

A few notes on the chart:

  • The Tab-Lock TABL20U starts at 235mm (9.25") tall where the Tab-Tite TAB20U starts at 241mm (9.5"); the maximums are the same.
  • TAB-SMU, TAB-SM2U and TAB-LGU are RAM's universal cradles, supplied with more than one set of cups so you can tune the fit.
  • Where RAM only publishes a maximum (TAB-SAM29U, TAB36U), the chart shows "up to".

My tablet isn't listed: will it fit?

Probably, if the numbers work. Tab-Tite fit is decided by size, not brand, so a tablet that sits inside a cradle's height, width and depth ranges will fit even if RAM never tested that exact model. If you're between two cradles, go for the one where your width sits comfortably inside the range rather than right on the limit. Still not sure? Send us your tablet model and case and we'll check it for you.

Cradle only, or a complete mount?

The RAM-HOL listings are the cradle on its own. To mount it you need a round ball base (B-size 1" or C-size 1.5"), a double socket arm and a base for your vehicle or surface. For the popular sizes we also list the cradle with a ball base already fitted, and complete kits with suction cup, drill-down, yoke clamp, Tough-Claw™ and RAM® Pod bases. The cradle you choose from this guide is the same in every kit that carries its SKU (for example, any kit ending in TAB20U uses the TAB20U cradle).

FAQs

Can I reuse my cradle when I change tablets?

Often, yes. The end cups are sold separately for most sizes, so if your new tablet suits a cradle that shares the same backplate you can swap the cups rather than buy a whole new holder. Check the replacement cup listing for your new size before ordering.

Do Tab-Lock cradles fit the same mounts as Tab-Tite?

Yes. Both use the 4-hole AMPS pattern (30mm x 38mm) and take the same RAM® B and C size round ball bases.

Is a Tab-Tite secure enough for a motorbike or off-road?

The spring tension holds well, and we'd use a C-size (1.5") ball mount for rougher work. For off-road or extreme use RAM recommends adding a tether as backup.

How fast will it ship?

Anything shown as in stock ships from our Auckland warehouse, normally within 1 business day. If a cradle shows as enquire, get in touch and we'll see what we can do.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.